Downloads
This software is used to test and setup the FieldServer or are needed for specific drivers as noted. This software is upgraded from time to time and the latest version is always available for download here at the FieldServer website. When installing these programs on your computer make sure that they are installed in the proper directory where the current version resides.
Click to go to download required:
- All FieldServers
- BACnet MS/TP - FS-8700-73
- ControlNet - FS-B3514-01
- ControlNet - FS-B4014-01
- DeviceNet - FS-B3515-01
- DNP3 - FS-8700-138 (Serial) and FS-8704-17 (Ethernet)
- EtherNet/IP - FS-8704-14
- Modbus Plus - FS-B4019-01
- Profibus DP - FS-B3512-01
- SlotServer
- SNMP
| Software | Size | Description | ||
|---|---|---|---|---|
| All FieldServers | ||||
| Install.zip | 8.0Mb | The Install.zip file contains all of the software and manuals needed to configure, analyze, monitor and operate the FieldServer and it is provided with all FieldServers on the Utility Installation Memory Stick. The latest version will always be available here on the website. If you already have the FieldServer Utilities loaded on your computer, you should remove the old files before installing the new ones. | ||
| Discovery.zip | 7.1Mb | The Discovery.zip file contains the "Discovery Utility" that is used to discover all FieldServers at a specific IP address network. | ||
| BACnet MS/TP Driver - FS-8700-73 for all FieldServers | ||||
| Setup_MSTP_Log.exe | 6.7kb | The MSTP Log Utility is used to capture BACnet MS/TP traffic. To use this utility, a RS-232/RS-485 converter or a USB/RS-485 converter must be used to connect the PC to the BACnet MSTP network. The utility will capture all of the MS/TP traffic and save it in a wireshark formatted file. WinPcap (available at Technical Resources page) must be downloaded on the PC in order for the utility to work. | ||
| FS-B3514-01 FieldServer Serial/Ethernet/ControlNet Gateway | ||||
| FServer.eds | 5.0kb | EDS files are simple text files specific to the product noted and used by network configuration tools to help you identify products and easily commission them on a network. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| FS-B4014-01 FieldServer Serial/Ethernet/ControlNet 10-port Gateway | ||||
| FServer.eds | 8.0kb | EDS files are simple text files specific to the product noted and used by network configuration tools to help you identify products and easily commission them on a network. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| Cnet.ss1 | 148.0kb | SS1 file is the ControlNet message capture module for shared memory. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| FS-B3515-01 FieldServer Serial/Ethernet/DevicelNet Slave Gateway | ||||
| FServer.eds | 5.0kb | EDS files are simple text files specific to the product noted and used by network configuration tools to help you identify products and easily commission them on a network. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| DNP3 Drivers - FS-8700-138 (Serial) and FS-8704-17 (Ethernet) for all FieldServers | ||||
| DNP3DeviceProfile.zip | 97.0kb | ZIP file contain all the files necessary to access the FieldServer_DNP3_Cap.xml DNP3 Capabilities file. Right-click on the title to the left and select "Save Link As..." and choose the proper directory to save the file. Then extract all five files in this ZIP file to a common directory. Then go to that directory and open FieldServer_DNP3_Cap.xml using Internet Explorer. | ||
| EtherNet/IP Driver - FS-8704-14 for all FieldServers | ||||
| FServer.eds | 3.0kb | EDS files are simple text files specific to the product noted and used by network configuration tools to help you identify products and easily commission them on a network. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| EIP_Card.ACD | 281.0kb | This is an example ACD file with RUN Logic so that only one message block is running at a time which is required by the FieldServer EtherNet/IP driver. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| SNMP Driver - FS-8704-26 for all FieldServers | ||||
| FServer-Std.MIB | 9.0kb | MIB (Management Information Bases) files contain information about the hierarchies, variables and other metadata on a device. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| FS-B4019-01 FieldServer Serial/Ethernet/Modbus Plus Multiport Gateway | ||||
| Bridge.sys | 1.0kb | SYS files are device configuration files for Modbus Plus, both the Bridge.sys and MBPHOST.sys files are necessary. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| MBPHOST.sys | 20.0kb | |||
| FS-B3512-01 FieldServer Serial/Ethernet/Profibus DP Slave Gateway | ||||
| FServer.gsd | 5.0kb | GSD (device data) files are simple text files which are required to configure a Profibus network. For each device with a Profibus interface there exists one definitive GSD file, which is identified by a unique identity code assigned by the Profibus User Organization (PNO). Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| SlotServer ControlLogix Communications Module - FS-RA-CLX-LON-000 only | ||||
| FServer.xif | 26.1kb | XIF (external interface files) files contain information about the variables on a device, including all necessary variable properties. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| SlotServer ControlLogix Communications Module - All versions | ||||
| FServer.eds | 2.0kb | EDS files are simple text files specific to the product noted and used by network configuration tools to help you identify products and easily commission them on a network. Right-click on the title to the left and select "Save Target As..." and choose the proper directory to save the file | ||
| Full_SlotServer.zip | 300.0kb | ACD files that demonstrate the use of multiplexing to page data through the SlotServer I/O buffer. This is appropriate for applications where a large amount of data is required to be transferred.. | ||
| Quickstart.zip | 264.0kb | ACD files that demonstrate a simple SlotServer application where only one "page" of inut and output buffer are needed to transfer all the required data. As a basic application, it contains all of the required configuration necessary for SlotServer communication. | ||
| Quickstart_UDT.zip | 272.0kb | ACD files that demonstrate a simple SlotServer application except that it illustrates the use of UDT's to clearly separate data from header information and add a documtneation set to a trmplate of data. | ||
FieldServer Technologies
1991 Tarob Court
Milpitas, CA 95035
Phone: 408-262-2299
Fax: (408) 262-2269
Toll-free: (888) 509-1970
Email: sales@fieldserver.com
